Print Friendly, PDF & Email

Installation and Maintenance Instructions

according to Regulation DIN 82079

suction lance

suction lance

 


Information about the Manufacturer

Giebel Filtec GmbH

Giebel FilTec GmbH
Carl-Zeiss-Str. 5
74626 Bretzfeld-Schwabbach
Germany

Phone +49 7946 944401 0
Fax +49 7946 944401 29
E-Mail info@giebel-adsorber.de

 


Product Overview

 

sal-bar-al sal-bar-al sal-bar-al sal-bar-al
SAL-BAR
1-Bypass
SAL-BAR
2-Bypass
SAL-LK
1-Bypass
SAL-LK
2-Bypass

 

Materials used:
Aluminium, stainless steel, FKM, EPDM

REACH notice:
No ingredients that must be named according to Regulation (EC) No. 1907/2006.

 


Structure and Materials

 

     SAL-BAR
1-Bypass
SAL-BAR
2-Bypass
SAL-LK
1-Bypass
SAL-LK
2-Bypass
Housing material Aluminium / Stainless Steel
Seal material FKM / EPDM
Pump connection BSP G ¾" inside
BSP G ½" inside
Adsorber connection BSP G ½" inside
BSP G ¾" inside
BSP G 1" inside
LK 73 (for accessories, e.g. filling adapter)
Drum/IBC connection BSP G 2" outside
LK 73
Operating temperature -40°C - +150°C

 


Technical Data

 

  sal-bar-al sal-bar-al sal-bar-al sal-bar-al
  SAL-BAR
1-Bypass
SAL-BAR
2-Bypass
SAL-LK
1-Bypass
SAL-LK
2-Bypass
Total weight [kg] 1,9 2,0 2,2 2,4
Diameter [mm] 70 70 85 85
Height [mm] 909 909 / 392 900 909 / 392

 


Montage und Inbetriebnahme Montage und Inbetriebnahme 

Installation and Commissioning

1. Check the seal for correct seating.
2. Screw the suction lance onto the drum/IBC/system.
3. Screw the hose for the pump into the lateral Thread.
4. Screw the adsorber into the upper thread of the suction lance.

Montage und Inbetriebnahme Montage und Inbetriebnahme

Montage und Inbetriebnahme


Maintenance

1. Unscrew the adsorber.
2. Unscrew the hose from the suction lance
    Remove the suction lance from the storage tank/system by unscrewing it.
4. Check seal for damages.
    If necessary, replace with new one.
5. Check ball valve in the foot part for mobility (for the valve version).
6. Screw the suction lance back onto the system/system/storage tank.

 


Risk and Hazard Analysis

1. Moist air flows into the storage container / the system
Porous Gasket
Moist air can flow into the system at the porous points. The seal must be checked according to the maintenance schedule.

2. Suction Lance is damaged
Material Resistance
The ambient and operating conditions should be taken into account in the selection.

Temperature Range
The ambient and operating temperatures should not exceed or fall below the specified range, otherwise the suction lance may be damaged.

Improper Handling
Incorrect or improper handling can damage the suction lance. Please pay attention to the recommended installation.

3. Over- or Underpressure builds up in the System
Ball valve clogged/glued
Check the ball valve for possible dirt or blockage.

4. Liquid flows out of the Suction Tube
Ball Valve blocked
Contamination could prevent the ball from closing properly and thus keep the liquid in the suction tube.

Giebel Filtec GmbH

5. Thread of the Adsorber and Accessories is damaged
When mounting the adsorber as well as the valve part on the system, the threads must be slightly wetted with oil. Failure to lubricate the threads can lead to rubbing of the individual threads and is no reason for complaint.

 

 


Maintenance Plan

1. Check seal for wear

Check    The seal installed on the suction lance must be checked to ensure it is in perfect condition. For this purpose the O-ring should be checked for brittleness.
Cycle    Annually
Measures    If damage is present, the seal should be replaced.

2. Check ball Valve for Wear

Check    Check the ball in the foot part of the suction lance for free movement.
Cycle    Annually
Measures    If the ball no longer opens or closes, it is recommended to replace the entire suction lance to ensure full functionality.

3. Visual Inspection of the Suction lance

Check    The suction lance must be checked visually for damage. Damage can occur due to various environmental or operating conditions or improper handling.
Cycle    Annually
Measures    If the suction lance is damaged, it should be replaced to ensure full functionality.

4. Replacing the Wearing Parts

Check    The wearing parts, especially the ball in the foot part of the suction lance must be checked with regard to their condition.
Cycle    Every two years
Measures    Regardless of the result of the test, it is recommended to replace the wearing parts to ensure smooth operation.

 


Contact and sales partner

Contact our contact persons and sales partners

We're here for you

You will receive an offer on the same day.
We are happy to advise you on short notice via video or
realize a personal appointment within one week.
You will receive a standard GIEBEL Adsorber within a week.

 

GIEBEL FilTec GmbH
Carl-Zeiss-Str. 5 | 74626 Bretzfeld | Germany
Phone: +49 79 46 94 44 01-0
E-Mail: info@giebel-adsorber.de